Bush Hog RFM 60 Návod k obsluze

Procházejte online nebo si stáhněte Návod k obsluze pro Sekačky na trávu Bush Hog RFM 60. Bush Hog RFM 60 Operator`s manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 20
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
ASSEMBLY
ll
OPERATION
ll
MAINTENANCE
04/09 Rev. 1 $4.00
50050226
RFM 60
Rear Finishing Mower
Operators Manual
BUSH HOG
®
Zobrazit stránku 0
1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - BUSH HOG

ASSEMBLYll OPERATION ll MAINTENANCE04/09 Rev. 1 $4.0050050226RFM 60Rear Finishing Mower Operator’s ManualBUSH HOG®

Strany 2 - CONGRATULATIONS!

2-1 ATTACHING TO TRACTORA. Attach to tractor Cat. I three point hitch asdescribed in tractor operator’s manual.SECTION IIPREPARATION FOR USEB. Raise a

Strany 3 - Operator’s Manual

G. Clamp end of driveline in a vice. Cut off shieldwhere marked. (Figure 2-3).Figure 2-3H. Using cut off section of shield as a guide, cutshaft the s

Strany 4 - LIMITED WARRANTY

SECTION IIIOPERATING INSTRUCTIONS3-1 GENERAL SAFETYOnly qualified people familiar with this operator’smanual and tractor operator’s manual should oper

Strany 5 - DEALER PREPARATION CHECK LIST

SECTION IVMAINTENANCE4-1 MAINTENANCE CHECK LISTPerform scheduled maintenance as outlined below.Lower implement to ground, turn off tractor, and setpar

Strany 6 - Signal Words

4-3 BELT ADJUSTMENTBelt tensions should be checked every 40 hours toget maximum life from drive belts and best perfor-mance from the cutter. Belt tens

Strany 7 - IMPORTANT SAFETY PRECAUTIONS

4-6 TROUBLESHOOTINGTroubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement partsare necessary, contac

Strany 8

THE FOLLOWING SAFETY PRECAUTIONSSHOULD BE THOROUGHLY UNDERSTOODBEFORE ATTEMPTING MACHINE ASSEMBLY.1. Wear personal protective equipment such as,but

Strany 9 - INTRODUCTION AND DESCRIPTION

E. Fasten mast supports and upper flex link tomast halves using 1/2 x 5” capscrew, pivot tube andlocknut.F. Place two long spacers on the caster stems

Strany 10 - PREPARATION FOR USE

SAFETY DECALSTo promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either

Strany 11

BOLT DIAMETERWRENCH (IN.) “B” AND SAE SAE SAESIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 87/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16)7/16 1/4 - 28 UNF

Strany 12 - OPERATING INSTRUCTIONS

CONGRATULATIONS!You have invested in the best implement of its type on the market today.The care you give your Bush Hog implement will greatly determi

Strany 13 - MAINTENANCE

2501 Griffin Avenue llSelma, AL 36703Telephone (334) 874-2700 llwww.bushhog.com

Strany 14 - 4-4 BELT REPLACEMENT

RFM 60Operator’s ManualTABLE OF CONTENTSSECTION/PARA PAGEWarranty . . . . . . . . . . . . . . . . . . . . . . . . . .2Dealer Preparation Check List

Strany 15

LIMITED WARRANTYOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOBush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from anauthorized

Strany 16 - DEALER ASSEMBLY

DEALER PREPARATION CHECK LISTRFM 60 Finishing MowersBEFORE DELIVERING MACHINE — The following check list should be completed.Use the Operator’s Manual

Strany 17

Safety Alert SymbolThis Safety Alert Symbol means: “ATTENTION! BECOME ALERT!YOUR SAFETY IS INVOLVED!”This symbol is used to call attention to safetypr

Strany 18 - SAFETY DECALS

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safetyprecautions that should be followed by theoperator to avoid accidents. When

Strany 19 - TORQUE SPECIFICATIONS

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS.*(This section is intended to explain in broad terms the concept

Strany 20

1-1 INTRODUCTIONWe are pleased to have you as a Bush Hog cus-tomer. Your RFM Rotary Cutter has been carefullydesigned to give maximum service with min

Komentáře k této Příručce

Žádné komentáře